Setters, Cranks and Stilts

There are various options to improve a firing, either used with or instead of standard kiln shelves. They offer a number of potential benefits:

  • the amount of ware that can be fitted into the kiln may be increased
  • the ratio of ware:kiln furniture may be increased, increasing firing efficiency
  • setters may help maintain the shape of ware in the kiln
  • cranks and stilts may allow the underside of the piece to be glazed

Setters

Setters are designed to support flat objects such as plates and tiles in a more efficient way than full size kiln shelves. At their simplest, they are discs with 3 lobes that may either contain integral spacer, or may be shaped to sit on standard kiln props. In the kiln they are stacked on top of each other. At the bottom of the stack there should be an air gap between the base of the setter and the kiln shelf, so if necessary the setter supports should be placed on blocks to raise it. Because of their small size, they can be considerably thinner than a full kiln shelf.

The benefits are:

  • better packing of the kiln
  • improved heat flow round the wares and throughout the kiln
  • a reduction in the total amount of kiln furniture


They may also be shaped to help maintain the shape of a piece in a high temperature firing, when the clay is likely to soften soften and deform. In this case, they are geared towards unglazed work, due to the potentially high contact area between the setter and the ware, so are best suited to the commercial pottery approach of making the bisque firing go to maximum temperature, and then use a lower temperature for the subsequent glaze firing. The setter may be anything from a simple disc to keep a rim round, to a support shaped to the underside of the ware to prevent it slumping.

Cranks

Cranks are similar to setters in allowing pieces to be stacked up vertically, but they are designed to support pieces on sharp points during the glaze firing, so that it can be glazed all over. This is important in making pieces fully watertight that are using clay which is not fully vitrified, but it can be used on any piece where you want to glaze the underside. The limitation of cranks is that the piece is not fully supported, so if it is fired to a high enough temperature that the clay softens the piece may deform.

The pins are generally made of metal or ceramics, and are discarded after the firing as they are likely to have glaze on them. Being thin and sharp, they leave a minimal mark on the glaze, which will generally not be noticed, or they can be polished out if necessary.

If there is any movement in the crank, this may scratch the glaze before the piece is fired. You can avoid the risk of this by filing any gaps with solid wax, which will keep things rigid until the kiln is loaded, and then burn out during the firing.

Stilts

Stilts are Y shaped metal or ceramic pieces, with sharp pins at the end of each arm. They are used in a similar way to cranks, but in conjunction with a normal kiln shelf or a flat setter. They are available in a wide range of sizes, to match your work - to large a size obviously won't work, and too small a size will make it difficult to balance the ware on top when loading the kiln, as well is increasing the risk of the piece slipping off as the shelves get jogged with more pieces being loaded. Generally the amount of glaze picked up by the stilts is so small that they can be flipped over to use a second time - though if there is any question of glaze getting onto the kiln furniture, discard them.

<HR>

Licence


Creative Commons Licence
Tim Thornton Ceramics Technical by Tim Thornton is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Permissions beyond the scope of this license may be available at https://tim-thornton.com/tikiwiki/tiki-index.php?page=Licence.
If you re-use any material from this web site, you must include an attribution statement as described in the licence, and state if the work has been altered.

You may release work that modifies or builds upon this work only under the same licence (or a compatable one, as defined in the licence).

This licence does not permit you to use this work for commercial purposes, i.e. for commercial advantage or monetary gain. If you wish to use the work in this way, please contact us to discuss it. You will need our prior permission and approval to do this.

Whilst we aim to ensure that all material is accurate at the time of publication, we do not accept responsibility for decisions based on information we make available. No content of this site may be taken to be legal or medical advice.

Please bear in mind that materials on the website are the most up to date versions, but items you have downloaded in the past may not be. The materials are updated from time to time. We recommend that you use the latest versions by referring to those published on our website.

Exclusions


Images – Images are not available for re use under the OGL because in most cases copyright is held by a third party. The Council does not grant anyone any rights to re use images.

Use of logos – The use of Tim Thornton’s logos on any document or in association with any information, signifies that the document or information has been prepared or approved by him. The logos are to be used only when reproducing materials unaltered from the web site, to show their original source. If you wish to use the logo in any other way, please contact us first to obtain permission.

Third party intellectual property/copyright – We do not have the legal authority to grant permission to re use documents where legal rights are owned by third parties.

Applications for re-use


If you wish to make a specific application to re use information which does not conform with the CC BY-NC-SA 4.0 licence terms, please contact us to ask permission and for details of what, if any, additional conditions and/or charges may apply. Your application should be in writing, specifying your name and address and, identifying the information source you want to re-use and the purpose for re-use.

Disclaimer


Whilst every care has been taken in the compilation of this website, and every attempt made to present up-to-date and accurate information, we cannot guarantee that inaccuracies will not occur. We will not be held responsible for any loss, damage or inconvenience caused as a result of any inaccuracy or error within these pages.

Links from our site may lead to pages maintained by other organisations. These are provided purely for your convenience, and do not imply that we endorse or support those organisations, the information on their pages, or their products or services in any way. Additionally, no responsibility is assumed by us for the contents of its pages.