Outdoor Lamps

Note that if the lamp is marked for indoor use only, and is not marked with an IP protection rating, this section does not apply.

Guide to IP ratings: https://www.iec.ch/ip-ratings
As a rule of thumb, the following is a guide to required IP levels for lights:

  • IPX3 will protect against continuous spray at up to a 60° angle, which is generally considered sufficient in partially enclosed or covered areas.
  • IPX4 is more commonly used as a minimum in more exposed spaces.
  • If the lights are likely to be cleaned using pressurised jets (e.g. if mounted close to the ground on a garden path or drive), they should be rated at IPX5 or above.
  • Any lighting intended for immersion (e.g. pond or pool lighting) up to a depth of 1m must be rated at least IPX7, but always check explicitly with the manufacturer before installing any lighting below the surface of the water.
  • Immersion at greater depths will require IPX8, and should again be checked explicitly for precise ingress resistance capabilities before installation.

If the lamp is not to be marked for indoor use, the lamp must be rated to at least IPx4 (where x can be any level of protection). This includes items such as where the cable enters the lamp.

Testing should be as per section 9 of EN 60598 - this over rides EN 60529 for lamps.

IEC 60598 for Luminaires vs. IEC 60529 for Enclosures - comparison of environmental protection requirements: https://kenall.com/Kenall-Files/Product-Files/Literature/Standards-IEC60598vs60529.pdf

PVC insulated cable is not suitable for external use - alternatives such as rubber insulated cable should be used instead.

Attention should be paid to corrosion of metals, either on the outside of the lamp, or on the inside due to corrosion. This involves both the corrosion resistance of the metal itself, and the possibility of corrosion due to two dissimilar metals being in contact (electrolytic or galvanic corrosion).

Plastics such as polystyrene, and materials such as cellulose, should not be used due to their susceptibility to sunlight or a wet environment.

The IP rating should be marked on the lamp, with other installation markings, and also included in the instructions. IP ratings of 20 or less do not need to be marked.

IPx1 to x6 rated lamps shall have a means of letting water out of the lamp, e.g. drain holes.

For IPx1 or higher rated lamps, where rusting of iron/steel components, or corrosion of aluminium components, may make the lamp unsafe, shall be tested to ensure that they are resistant to corrosion.

The requirement to sell lamps with a UK plug attached still applies even though the plug cannot be waterproof, but the lamp instructions must tell the user how to make a connection to the same IP level as the rest of the lamp, e.g. using a waterproof socket and cover, or changing the plug for an alternative waterproof option.



Creative Commons Licence
Tim Thornton Ceramics Technical by Tim Thornton is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Permissions beyond the scope of this license may be available at https://tim-thornton.com/tikiwiki/tiki-index.php?page=Licence.
If you re-use any material from this web site, you must include an attribution statement as described in the licence, and state if the work has been altered.

You may release work that modifies or builds upon this work only under the same licence (or a compatable one, as defined in the licence).

This licence does not permit you to use this work for commercial purposes, i.e. for commercial advantage or monetary gain. If you wish to use the work in this way, please contact us to discuss it. You will need our prior permission and approval to do this.

Whilst we aim to ensure that all material is accurate at the time of publication, we do not accept responsibility for decisions based on information we make available. No content of this site may be taken to be legal or medical advice.

Please bear in mind that materials on the website are the most up to date versions, but items you have downloaded in the past may not be. The materials are updated from time to time. We recommend that you use the latest versions by referring to those published on our website.


Images – Images are not available for re use under the OGL because in most cases copyright is held by a third party. The Council does not grant anyone any rights to re use images.

Use of logos – The use of Tim Thornton’s logos on any document or in association with any information, signifies that the document or information has been prepared or approved by him. The logos are to be used only when reproducing materials unaltered from the web site, to show their original source. If you wish to use the logo in any other way, please contact us first to obtain permission.

Third party intellectual property/copyright – We do not have the legal authority to grant permission to re use documents where legal rights are owned by third parties.

Applications for re-use

If you wish to make a specific application to re use information which does not conform with the CC BY-NC-SA 4.0 licence terms, please contact us to ask permission and for details of what, if any, additional conditions and/or charges may apply. Your application should be in writing, specifying your name and address and, identifying the information source you want to re-use and the purpose for re-use.


Whilst every care has been taken in the compilation of this website, and every attempt made to present up-to-date and accurate information, we cannot guarantee that inaccuracies will not occur. We will not be held responsible for any loss, damage or inconvenience caused as a result of any inaccuracy or error within these pages.

Links from our site may lead to pages maintained by other organisations. These are provided purely for your convenience, and do not imply that we endorse or support those organisations, the information on their pages, or their products or services in any way. Additionally, no responsibility is assumed by us for the contents of its pages.