Electric Lamps
The contents of this page are being moved over to the Making Electric Lamps section - go over there for more detailed information.
As soon as electricity is concerned, the regulations become more complex. But, as an alternative to producing a complete lamp, you may want to consider creating just the lamp base, letting your customer add the electrical side (easily done from kits available from a number of suppliers) and the lampshade.
At present I'm just covering the UK/EU regulations.
Lamp Wiring Tips
Stability: minimum 6° tilt angle
Class I holders (generally metal) require earthing with a 3 core cable. Class II holders (generally plastic) are non conducting, so only need a 2 wire cable and no earthing.
The lamp fittings need to be secured to withstand at least 2Nm force - a hard twist. Look at gluing components in place as a backup to retaining screws.
Plugs will be marked to BS1363 or ASA. Only use a 3A fuse.
For an Edison screw bulb holder, it is important that the Neutral (blue) wire is connected to the screw part, not the Live (brown) wire
Testing: just continuity and resistance testing with a multimeter, and PAT testing, is not enough. Test every item just before packaging it.
Regulatory Requirements
Here are a number of guides to lighting regulations - though note that regulations change with time, so some of the information may be out of date.
When looking at the EU regulations, you need to be aware that they refer to the light bulb as a lamp, and to what we call a lamp is referred to as a luminaire.
Lighting Europe check list and requirements for luminaires in the EU
ComplianceGate info on LED Lighting in the EU
PAT Testing Training guidance on making and testing lamps
EMC and Low Voltage Directives
These are for the CE mark required by all electrical products. For luminaires, the key points are:
- Compliant CE and WEEE markings, manufacturer's info etc
- Rated voltage, and maximum wattage of replacement bulbs
- Class II symbol if the luminaire is not earthed. If it is earthed (Class I) are all metal parts exposed to the user earthed?
- Does the lamp holder comply with the relevant standards
- Is the user protected against access to live parts, either when in use or when changing the lamp?
- Is the power cable protected against sharp edges, e.g. where it enters the luminaire? Is it protected against being pulled or twisted? And is there the correct plug fitted to the end?
- Safety and lack of interference from electronic controls, dimmers etc. - if you source these from reputable manufacturers they shouldn't be a problem
The good thing about these directives are that for many products, including luminaires, you can self-certify compliance rather than paying a test house to do this.
Note that as a result of Brexit if selling in the UK (except Northern Ireland) you need to use the UKCA mark, or the CE mark if selling in to the EU or Northern Ireland.
WEEE
See WEEE
RoHS
You need to be able to show that the lamp contains no harmful substance.
See here for more info on this in the UK
Eco-Design Requirements
This now applies to lamps (now light sources) as opposed to luminaires (now containing products).
However, note that some types of lamps are being phased out, so it does not make sense to design a new product to use them:
From September 2021, most halogen lamps and CFLi were phased out
From September 2023 most halogen lamps with a G4, G9 or GY6.35 base, and T8 linear fluorescent lamps, will be phased out
Energy Labelling of Electric Lamps and Luminaires
It used to be a requirement that luminaires had to be labelled regarding use of energy efficient lamps etc., but this is no longer the case. If you sell lamps in their original packaging, and the lamp complies with EU legislation, there is nothing more to do,
Switches
Switches are generally either integral with the bulb holder, or inline in the cable before it gets to the lamp.
Switches in the bulb holder avoid scrabbling down the cable to find the switch, but against this reaching for a switch at the top of the lamp could cause it to topple over if the user is clumsy. This type of switch is common in bulb holders for Bayonet bulbs, but less so in holders for Edison bulbs as it is harder to build into the bulb holder.
Having the switch in the cable avoids any instability problems, but the user has to find the lead and then find the switch on it, which means that the lead cannot be hidden away. Or, if it is a foot switch, they may be standing in the wrong position.
Cables and Cable Protection
For strength, and to comply with the Low Voltage Directive, a cable cross-section at least 0.75mm² should be used. If the lamp doesn't need to comply with the LVD, and the total weight is less than 1kg and cable length is less than 2m then 0.5mm² is OK. If putting multiple bulbs onto the lamp, also check the power capacity - 0.5mm² is rated to 3A, and 0.75mm² to 6A.
Cable should be to BS6500 or marked with <HAR> in the UK.
If the lamp does not need earthing, you just need 2 core cable; if it needs earthing, you need 3 core cable and an earthed plug.
Where the cable enters the body of the lamp, you will need to have a grommet to protect the cable from abrasion, and also a cable clamp to provide strain relief, so that the electrical connections are not strained when someone trips over the cable. Tying a knot in the cable is not seen as being sufficient. Both of these items need to be matched to the size and cross-section of the cable, and the grommet also needs to match the wall thickness of the lamp. Use a cable clamp that will withstand at least 60N force.
Summary Legislation and Standards
EU Legislation
| Directive or Regulation | Name | Notes | |
| 2006/95/EC | LVD - Low Voltage Directive | Voltages 50 - 1000V AC or 75 - 1500V DC | |
| 2004/108/EC | EMC - Electromagnetic compatability | Not applicable to devices without electronic components | |
| 2012/19/UE | WEEE - Waste from electrical and electronic equipment | ||
| 2011/65/EU | RoHS - Restriction of the use of certain hazardous substances | ||
| 2009/125/EC, 2019/2020 | Single Lighting Regulation | 2019/2020 replaces 245/2009, 1194/2012 and others | |
| 2010/30/EC, 2019/2015 | Energy labelling | ||
| 2001/95/CE | General product safety | ||
Note that the following EU legislation has been withdrawn, and references to it should be ignored:
- Directive 2000/55/EC - Energy efficiency requirements for ballasts for fluorescent lighting - withdrawn 12 April 2010
- Directive 2005/32/EC and Regulations 244/2009 and 245/2009 - Ecodesign requirements for fluorescent lamps without integrated ballast, for high intensity discharge lamps, and for ballasts and luminaires able to operate such lamps - withdrawn 31 August 2021
- Directive 2009/125/EC and Regulation 1194/2012 - Ecodesign requirements for directional lamps, light emitting diode lamps and related equipment - withdrawn 31 August 2021
- Directive 2010/30/EU and Regulation 874/2012 - Energy labelling of electrical lamps and luminaires - withdrawn 31 August 2021
Regulation 2017/1369 - Energy labelling of electrical lamps and luminaires - withdrawn 31 August 2021
UK Legislation
At present the UK legislation is in synch with the EU's, but consideration is being given to additional changes, such as phasing out less energy efficient types of light sources as LED equivalents become available.
The Ecodesign for Energy-Related Products and Energy Information (Lighting Products) Regulations 2021 - this incorporates EU legislation 2010/30/EC, 2019/2015 and 2009/125/EC, 2019/2020
Standards
A list of all Low Voltage Directive related standards
| Standard | |||
| Electromagnetic compatability | EN 55015 | ||
| Lamp holders - Edison | EN 60238, BS5042 | ||
| Low Voltage | EN 60598-1 (general requirements and tests) | ||
| EN 60598 2-1 (fixed general purpose luminaires) | |||
| EN 60598 2-2 (recessed luminaires) | |||
| EN 60598 2-4 (portable general purpose luminaires i.e. table or floor lamps | |||
| EN 60598 2-7 (portable luminaires for garden use | |||
| EN 60598 2-10 (portable luminaires for children | |||
| Miscellaneous lampholders | EN 60838 | ||
| EN 61000-3-2 | |||
| EN 61000-3-3 | |||
| Lamp holders - Bayonet | EN 61184, BS5042 | ||
| EN 61547 | |||
| Assessment of lighting equipment related to human exposure to electromagnetic fields | EN 62493 (lamps with just switches, dimmers, sensors etc. are deemed to comply without testing) | ||
| Lamp holders - Bayonet with advanced safety | BS5042, BS7895 | ||
| UK plug | BS1363 | ||
| UK cabling | BS6500 | ||
Standards Online
These are generally not meant to be posted online, as it is a breach of copyright and the conditions of purchase, so don't be surprised if they disappear!
| Standard | Document | Notes | |
| BS EN 60598-1:2015 | https://dganmai.com/uploads/soft/200714/en/EN%2060598-1_2015.pdf | ||
| BS EN 60598-1:2015 Addendum 1:2018 | http://bqw.csstgc.com.cn/userfiles/ec09abd3793445079490d6a8a3c28e42/files/teckSolution/2022/01/BS%20EN%2060598-1-2015+A1-2018.pdf | Contains parts of sections 10, 11 and 13 - not sure if these are all the changes in the addendum | |
Standard Tests Results
Documents giving the results of testing an item to a given standard.
| Item Tested | Standard(s) | Document | Notes |
| LED Wall Lights | EN 60598, 61347, 62031, 62471, 62493 | BHa-Bhb-BHc-Test-Report-1.pdf | |
| Wi-Fi smart lamp holder | EN/ISO 60598, 61347, 60238, 62493 | SONOFF_SlampherR2_LVD_Safety_Test_Report_3.pdf |
Declaration of Conformity and Technical File
The Technical File is an internal document in which you show how you know that your lamp complies with the relevant regulations. There is no need to make this public, except in any situation where you have to show your compliance.
The Declaration of Conformity is a piece of paper that needs to accompany your lamp, stating that you comply with specific regulations. You can incorporate it into other paperwork, such as the user instructions.
These need to cover the following regulations and standards:
| Directive or Regulation | Name | ||
| 2006/95/EC | LVD - Low Voltage Directive | ||
| 2004/108/EC | EMC - Electromagnetic compatability | ||
| 2011/65/EU | RoHS - Restriction of the use of certain hazardous substances | ||
| 245/2009, 347/2010, 1194/2012 | Ecodesign | ||
| 874/2012 | Energy labelling (only Technical File) | ||
Retailer Requirements
Once again, the larger retailers may have their own additional requirements, based on experiences from their customers.
Tilt Test
Testing stability at 6°, 12° and 15° at all angles of rotation. If it fails the test at 6°, then an additional thermal test is required to make sure nothing gets too hot and is damaged by the heat, or causes a fire.
Regulatory Check List
| Item | Requirement | Notes | |
| For UK excluding N. Ireland | UKCA mark | UKCA mark visible, legible and indelible on lamp or packaging | |
| For EU and N. Ireland | CE mark | CE mark visible, legible and indelible on lamp or packaging | |
| Maker's identification | Required | Maker, distributor or importer | |
| Model No. | Required | May be model or serial number | |
| Rated voltage | Required | May be a range, e.g. 220 - 240V | |
| Rated Wattage | Required | Only for bulb replacement | |
| IP rating | Optional | Only required if not IP20 | |
| Class II symbol | Optional | Only required if connected to mains and not earthed | |
| Class III symbol | Optional | Only required if voltage below 50V AC or 120V DC | |
| WEEE symbol | Required | Importer/manufacturer should be WEEE registered, and their details in the WEEE database | |
| Instruction sheet | Required | All info for installation, use and maintenance, in the language of the country where sold | |
| Declaration of Conformity (DoC) | Required | ||
| Physical Checks | |||
| Sharp edges that may damage the wire insulation | None | ||
| Cord anchorage to prevent mechanical stress on the connections | Required | Only for table or floor lamps | |
| Lampholder compliant with the standard | Required | ||
| No access to live parts | Required | After installation, when it is in use or when the bulb is being replaced | |
| Class I Earthing | Required | All metal parts close to live parts or wiring, and accessible in normal use or when changing bulbs, must be earthed | |
| Plug fitted and of the right type for the country being sold in | Required | Only for floor and table lamps | |
Lighting Industry Association - trade body
<HR>Licence
Tim Thornton Ceramics Technical by Tim Thornton is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Permissions beyond the scope of this license may be available at https://tim-thornton.com/tikiwiki/tiki-index.php?page=Licence.
If you re-use any material from this web site, you must include an attribution statement as described in the licence, and state if the work has been altered.
You may release work that modifies or builds upon this work only under the same licence (or a compatable one, as defined in the licence).
This licence does not permit you to use this work for commercial purposes, i.e. for commercial advantage or monetary gain. If you wish to use the work in this way, please contact us to discuss it. You will need our prior permission and approval to do this.
Whilst we aim to ensure that all material is accurate at the time of publication, we do not accept responsibility for decisions based on information we make available. No content of this site may be taken to be legal or medical advice.
Please bear in mind that materials on the website are the most up to date versions, but items you have downloaded in the past may not be. The materials are updated from time to time. We recommend that you use the latest versions by referring to those published on our website.
Exclusions
Images – Images are not available for re use under the OGL because in most cases copyright is held by a third party. The Council does not grant anyone any rights to re use images.
Use of logos – The use of Tim Thornton’s logos on any document or in association with any information, signifies that the document or information has been prepared or approved by him. The logos are to be used only when reproducing materials unaltered from the web site, to show their original source. If you wish to use the logo in any other way, please contact us first to obtain permission.
Third party intellectual property/copyright – We do not have the legal authority to grant permission to re use documents where legal rights are owned by third parties.
Applications for re-use
If you wish to make a specific application to re use information which does not conform with the CC BY-NC-SA 4.0 licence terms, please contact us to ask permission and for details of what, if any, additional conditions and/or charges may apply. Your application should be in writing, specifying your name and address and, identifying the information source you want to re-use and the purpose for re-use.
Disclaimer
Whilst every care has been taken in the compilation of this website, and every attempt made to present up-to-date and accurate information, we cannot guarantee that inaccuracies will not occur. We will not be held responsible for any loss, damage or inconvenience caused as a result of any inaccuracy or error within these pages.
Links from our site may lead to pages maintained by other organisations. These are provided purely for your convenience, and do not imply that we endorse or support those organisations, the information on their pages, or their products or services in any way. Additionally, no responsibility is assumed by us for the contents of its pages.